COLECTION FORMAT & PHONE LOCK CHINA PHONE By INFINITY RX TX PIN FINDER SUKSES FULL

N95 pda dual sim card format sukses full

software version: 1.14
cable type: 1x18 (L18A)
platform: MT: MT6205, MT6217-MT6228, MT6230
searching adapter at COM9...
adapter found, version: 2000
pins: 18, plain
power cycles: 1
activation cycles: 7
power-off delay: 20
start Rx/Tx: 1/1
Loading configuration...
Initializing...
Press and HOLD phone Power button now !
detecting pins...
19200 fixed
CPU: MT6226
result: Rx:7 Tx:9
time required: 59 sec
Power On !
saved: n95_model_pda_2sim

COM9 [VCP2] selected
module v2.69
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:8BC2:01BB
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: E553_XZY4.00.0_26S01
Version: M500Z_05C_HW
detecting structure #2...
done
60 byte(s) read
imei: 35711100005341
connection Ok
building list...
done
items to clear: 209
warning: wrong packet cs
warning: wrong packet cs
209 of 209 items cleared
building list...
done
0 items remains
Finished, time used: 38 sec
Remove/Install battery now !

K-toch A905 Sukses Format

software version: 1.14
cable type: 1x18 (L18A)
platform: MT: MT6205, MT6217-MT6228, MT6230
searching adapter at COM9...
adapter found, version: 2000
pins: 18, plain
power cycles: 1
activation cycles: 7
power-off delay: 20
start Rx/Tx: 1/1
Loading configuration...
Initializing...
Press and HOLD phone Power button now !
detecting pins...
19200 fixed
CPU: MT6228
result: Rx:14 Tx:13
time required: 107 sec
Power On !
saved: k-toch_A905


COM9 [VCP1] selected
module v2.66
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:0101
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6228,E02
Date: 2004.07.02
Version: 1.0
Version: 092740_67C_V0067
Version: TIANYU28_06A_HW
detecting structure #2...
0 done
42 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
building list...
done
items total: 180
items to clear: 180
warning: wrong packet cs
180 of 180 items cleared
building list...
done
items remains: 0
Finished, time used: 48 sec
Remove/Install battery now !

phone lock hitech H39

COM5 [VCP5] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: unlock
unlock method: standard
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:FA0C:6220
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:2AEA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:2AEA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:2AEA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:2AEA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 2A0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.F72D7F14.[U26_06B_PCB01_GPRS_MT6226_S01.UPU25U26V04B22.BIN_8 0D0B014].rpl
New firmware detected:
U26_06B_PCB01_GPRS_MT6226_S01.UPU25U26V04B22.BIN

- make "Read full flash" operation
- send "backup_system_log_..." file to support: mt62xx@gmail.com
- send flash backup file(s) to support: mt62xx@gmail.com
- include in your e-mail full text from phone back label (phone name etc.)
identification#1 detection finished
device-id: F72D7F14
identification#1 protocol ver: 04
ver. sw1: U26_06B_PCB01_GPRS_MT6226_S01.UPU25U26V04B22.BIN
ver. sw2: UPU25U26V04B22, EB4F2F7F
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: EC257E25082501:2AEA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
detecting ffs structure pass 1...
.....................
detect standard fat location pass #1...
.................................................. ......
detect extended fat location pass #1...
.................................................. .....
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #1 detected ok
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading [eeprom[U26_06B_PCB01_GPRS_MT6226_S01.UPU25U26V04B22.BIN]]...
file saved: D:\INFINITY\new set-up\infinity\FlashFile\HITECH H39\backup_eeprom[U26_06B_PCB01_GPRS_MT6226_S01.UPU25U26V04B22.BIN]_20080605-114856.B0E.bin
flash: EC257E25082501:2AEA0000000000
Backup required data Done
Patch required data...
detection procedure, wait...
detection procedure completed
Patch required data Done
Special operation...
Special operation Done
Write...
flash: EC257E25082501:2AEA0000000000
Write: eeprom
Write Done
Finalization...
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log _F72D7F14_U26_06B_PCB01_GPRS_MT6226_S01.UPU25U26V0 4B22.BIN_80D0B014_20080605-114950.B0X.bin
Finished, time used: 267 sec
Remove/Install battery now

sukses format k-touch

software version: 1.14
cable type: 1x18 (L18A)
platform: MT: MT6205, MT6217-MT6228, MT6230
searching adapter at COM9...
adapter found, version: 2000
pins: 18, plain
power cycles: 1
activation cycles: 7
power-off delay: 20
start Rx/Tx: 1/1
Loading configuration...
Initializing...
Press and HOLD phone Power button now !
detecting pins...
19200 fixed
CPU: MT6226
result: Rx:14 Tx:13
time required: 108 sec
Power On !
saved: k-touch_a650

COM9 [VCP7] selected
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:0C7C:8FC0
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: 072142_500_V0750
Version: TIANYU26_06A_HW
detecting structure #2...
0 done
42 byte(s) read
imei: 35879000716041
connection Ok
building list...
done
items total: 195
items to clear: 195
warning: wrong packet cs
195 of 195 items cleared
building list...
done
items remains: 0
Finished, time used: 39 sec

Remove/Install battery now !

MITO 288GG SUKSES

software version: 1.14
cable type: 1x18 (L18A)
platform: MT: MT62xx (autodetect)
searching adapter at COM9...
adapter found, version: 2000
pins: 18, plain
power cycles: 1
activation cycles: 7
power-off delay: 20
start Rx/Tx: 1/1
Loading configuration...
Initializing...
Press and HOLD phone Power button now !
detecting pins...
19200 fixed
CPU: MT6226
result: Rx:7 Tx:9
time required: 59 sec
Power On !
saved: mito_288gg

COM9 [VCP2] selected
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:B5B2:4B50
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: E550_A5INDO.01.3_26S01
Version: M500Z_05C_HW
detecting structure #2...
done
60 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
building list...
done
items to clear: 199

MYTEC Model 928 (blutooth)

software version: 1.06
cable type: 1x8 (L8A)
platform: MT62xx (autodetect)
searching adapter at COM9...
adapter found, version: 2000
pins: 8, plain
power cycles: 1
activation cycles: 7
power-off delay: 20
start Rx/Tx: 1/1
Loading configuration...
Initializing...
Press and HOLD phone Power button now !
detecting pins...
19200
CPU: MT6226
result: Rx:2 Tx:3
time required: 5 sec
Power On !

COM9 [VCP2] selected
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:17CC:F1B0
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: ZL32L_THL1.6
Version: ZX26_05C_HW
detecting structure #2...
done
60 byte(s) read
imei: 35972500012745
connection Ok
building list...
done
items to clear: 183
130 of 183 items cleared
0 items remains
Finished, time used: 274 sec
Remove/Install battery now !